DUPLICATOR Model: RMC888

Operating Instruction

1. PART NAME AND FUNCTIONS

圓角矩形圖說文字: CONNECTOR

2. DUPLICATING

Setting Procedure	Status Display	Features
1. Plug the adapter into any convenient AC outlet.	0.0	frequency display
2. Press the 1 (SETTING) button	r –– 1	ready for reading—waiting for copy 1^st code.
3. Code reading place original transmitter in top of *TEST AREA*, press onto button 1. and holding the button till display shows done.	done
	1. A–10	for use our B type REMOCON
	2. b–10
	3. b–04
	4. r e t y	Press the 1 (setting), and retry
	5. E–10	code has not successful been read if flashed. repeat 2. or press 12 (RESTART) if required
4.	r –– 2	Waiting 2^nd code enter
5. press onto button 2(original transmitter)	––––	Repeat above step 3. if required
6. wiring the to duplicator via cable connector, press 2 (DUP.)button.	P–––	Code is duplicating into REMOCON
	LED display shows PA10, Pb10, Pb4, 10-04, 04-10, now the code has been duplicated into REMOCON successfully.
7. Tuning frequency a. press 1 (SETTING) b. place original transmitter in top of *TEST AREA, press either button. c. place REMOCON in top of TEST AREA,* press either button, then tunes frequency to be identified with original transmitter.	0.0 390.1	LED display shows frequency of original transmitter For example 390.1MHz(please refer fig.1)

Fig. 1(RMC535)

3. VARIFYING(if required)

Setting Procedure	Status Display	Features
1. press 3 (CHECK) button	Chec	Enter into CHECK function
press the button 1 on the REMOCON	––––	code reading (press and holding the button till Display shows done)
	done	code reading completed
	L––1	“button 1” confirmed
2. press the button 2 on the transmitter	––––	code reading (press and holding the button till display shows done)
	done	code reading completed
	L––2	confirm accurate “button 2”
3. repeat step above if required	no––	code reading unable to confirm. But it doesn’t mean the duplicating failure, particularly for b-04 .
3. repeat step above if required	no––	repeat step 2. And 3.

4. REDUPLICATING(requires REMOCON remote transmitter only)

Provide quantities capability

Setting Procedure	Status Display	Features
1. wiring the original transmitter to RMC888 via cable connector, press 13(REDUP.) If above step appeared	r–––	code reading
	r A 1 0	code reading completed
	Pb04 or Pb10	code reading completed
	E––05	failed in code reading, please check cable connector or transmitter.
2. wiring the REMOCON to Duplicator via cable connector, press 2 (DUP.)	p–––	code duplicating into REMOCON
	P A 1 0	duplicate completed for A type
	Pb04, Pb10	duplicate completed for B type

ERROR READING

Status Display	Trouble shooting
E - 02	Failed in duplicating, please check if the connector fixed securely.
E - 03	Failed in duplicating, please check if the connector fixed securely.
E - 05	Failed in reduplicating, please check if the connector fixed securely.
E –10	Reading failed, please re-operate.
E –12	“Long Code” receives from original transmitter, unable to duplicate into button 5^th and 10^th.
E –20	Can’t not be duplicated by A type transmitter, please replace to B type.

*Above messages will be indicated as flash sequentially. Press 1 (SETTING) to keep operating.

5. DUAL FREQUENCY DUPLICATING( For Dual Frequency Transmitter only)

Setting Procedure	Status Display	Features
1. Press 23(DUAL FREQ.) button	r1 1 1	Dual frequency duplicating mode
2. Press 23(DUAL FREQ.) button	r1 2 1	Dual frequency duplicating mode
3. Press 23(DUAL FREQ.) button	r––1	Single frequency duplicating mode
4. Following the above duplicating procedures.		Please refer above methods.

圓角矩形圖說文字: Remote Buttons

r 1 2 1

圓角矩形圖說文字: Position of Slide SW.

Fig. 2(RT-103)

6. ADVANCE DUPLICATE FUNCTION FOR DUAL FREQUENCY

Provide only dual frequency transmitters(REMOCON)

Transmitter(REMOCON) Set SW.	Status Display		Transmitter(REMOCON) Remote Button
Transmitter(REMOCON) Set SW.	1^st frequency	2^nd frequency	Transmitter(REMOCON) Remote Button
SW-1	r 1 1 1	r 1 2 1	1
	r 1 1 2	r 1 2 2	2
	r 1 1 3	r 1 2 3	3
	r 1 1 4	r 1 2 4	4
SW-2	r 2 2 1	r 2 1 1	1
	r 2 2 2	r 2 1 2	2
	r 2 2 3	r 2 1 3	3
	r 2 2 4	r 2 1 4	4

CHART 1

While transmitter Set SW. setting on SW-1, both of them can transmit either 1^st or 2^nd frequency. Identically while setting on SW-2, both of them can transmit either 2^nd or 1^st frequency.

For example 1.: While duplicate two original transmitters(X+Y) into one dual frequency transmitter(REMOCON), when transmitter(REMOCON) setting on SW-1, please follow following duplicate procedures:

1. Wiring the transmitter(REMOCON) to duplicator via cable connector. Press23 (SETTING) until LED display reads…r 1 1 1.

2. Press the first desire code duplicate button from original transmitter(X), LED display reads…r 1 1 2.

3. Press the second desire code duplicate button from original transmitter(X), LED display reads…r 1 1 3.

4. Press 23(DUAL FREQ.) button, LED display reads…r 1 2 1.

5. Press 1 (SETTING) button until LED display reads…r 2 2 1.

6. Press the first desire code duplicate button from original transmitter(Y), LED display reads…r 2 2 2.

7. Press the second desire code duplicate button from original transmitter(Y), LED display reads…r 2 2 3.

8. Press 2 (DUP.), LED display reads…P X X X, which means code duplicate completed.

For example 2.: While duplicate two original transmitters(X+Y) into one dual frequency transmitter(REMOCON), when transmitter(REMOCON) setting on SW-1

1^st frequency—X original transmitter for button 1 and 2

2^nd frequency—Y original transmitter for button 3 and 4

please follow following duplicate procedures: